Universal Recorder EDX-100A
Add to Wishlist
Available with 1 2 and 4 slotsLAN port for establishing multichannel network(Max. 256 channels)
Availability:
1 in stock
Contact for a quote.
Request for Quotationช่องทางการสั่งซื้ออื่น ๆ
ติดต่อทาง Line
@santatech
ติดต่อทางอีเมล์
santatech@gmail.com
ติดต่อทางโทรศัพท์
02-1013454
Description
The EDX-100A is a data recorder for measuring up to 256 channels.
Various conditioner cards are available for wide applications.
Specifications
| Models |
EDX-100A-1 (With DCS-100A) EDX-100A-1-0 EDX-100A-1-1 (With DCS-100A and DCS-101A) |
|---|---|
| Max. Channels | 8 |
| Analog Input |
Optional conditioner cards Implement with DPM, CDV, CTA, CFV, CCA, CVM installed |
| CAN Data Input | Accepts one card of CAN-41A |
| Voice Memo Input |
1 channel. Record voice memos included with recordings alongside with measurement data (during manual measurements) using a dedicated remote control(optional accessory) |
Sampling Frequency
| Sampling Methods | Synchronous sampling of all channels |
|---|---|
| Sampling Frequency Series |
1Hz to 100kHz(1-2-5 series): for 1 channel measurement 1Hz to 10kHz(1-2-5 series): for 16 channel measurement 1Hz to 5kHz(1-2-5 series): for 32 channel measurement 1Hz to 1kHz(1-2-5 series): for CAN data measurement |
| Data Storage |
CF cards recommended by Kyowa (128 MB to 8 GB; 45× speed or higher) Offline data transfer to computers is enabled after the recording is complete |
|---|---|
| Setting Conditions |
Online: From the PC via LAN or USB port Offline: By reading from the CF card which has measuring conditions written with the DCS-100A data acquisition software |
| Saving Conditions | Amplifier setting conditions and measuring conditions are saved in the internal nonvolatile memory, enabling immediate setup with previous conditions upon power-on. |
Measuring Modes
| Manual |
Data recording is manually started or stopped when data is recorded to a preset number of measured data. Manual mode allows recording of voice memo during data recording. |
|---|---|
| Trigger |
Data recording is automatically started when the preset trigger condition is satisfied. Note that any CAN data mustn't be used as trigger condition |
| Interval | Data recording is periodically made at preset intervals. |
| Manual Start/Stop of Data Recording | Possible by using the PC or by pressing the switch on the front panel or from the dedicated remote control unit |
|---|---|
| Balance Adjustment | Strain input channels are balanced by pressing the BAL. switch on the front panel or from the dedicated remote control unit or from the PC. |
| Saved Data Format | Kyowa standard format KS2, which enables data analysis with the optional Data Analysis Software DAS-200A |
| Collecting Data | LAN or USB port enables online data transfer to the PC, while CF card enables offline data transfer. |
| TEDS |
Reads sensor's information and sets to channel condition automatically. [Supported conditioner cards] CDV-40B (-F) DPM-42B (-F) DPM-42B-I (-F) CCA-40A (-F) CDV-44AS CDA-44AS/45AS CVM-41A AD-40AS (-F) |
| Synchronous Operation |
Synchronous cable enables cascade connection of up to 8 units of the EDX-100A. While data is recorded as a separate file in the CF card inserted into each unit, files of all cards are combined into a single file after online or offline data transfer to the PC. |
| Analog Output |
All, except for CDV-40B (-F), AD-40AS (-F), and CAN-41A. Conditioner cards provide an analog output connector, enabling voltage monitoring (±5 VFS). |
| CF Card Slot | 1 (For data recording and condition setting) |
Interfaces
| LAN and USB (For control and data transfer), switchable | |
| LAN I/F |
10BASE-T/100BASE-TX Connector: RJ45 modular jack |
| USB I/F |
Conforms to USB 2.0 (High speed). Connector: Series B receptacle |
| Operation Switches |
REC/PAUSE: Starts/pauses data recording. STOP: Stops data recording. BAL.: Executes balance adjustment. READ: Reads and sets conditions. ID: Sets ID No. of EDX-100A. LAN/USB: Switches communication port. |
|---|---|
| Indicators |
Operation status indicator LEDs: 7 Channel status indicator LEDs: The number corresponds to the number of channels provided. |
| External Control Connectors |
CONT IN and CONT OUT (For remote control and synchronous operation) |
| Operating Temperature | 0 to 50ºC |
| Operating Humidity | 20 to 90% (Non-condensing) |
| Storage Temperature | -20 to 60ºC |
| Vibration Resistant |
±29.42 m/s2 (3 G), 5 to 55 Hz (When operating) ±49.03 m/s2 (5 G), 5 to 55 Hz (When not operating) |
| Impact Resistant | 196.1 m/s2 (20 G) /11 ms |
| Power Supply |
10 to 18 VDC Connector: RM12BRD-4PH (Hirose) DC power supply or optional dedicated AC adapter is required. |
| Current Consumption |
Approx. 1.2 A (When operated on 12 VDC with 1 CDV-40B card mounted and full load applied) |
| Dimensions | 70.0 W x 132.5 H x 255 D mm (Excluding protrusions) |
| Weight |
1.6 kg (1.7 kg with 1 CDV-40B card mounted) |
| Standard Accessories |
DC power cable P-76 Ground wire P-72 USB cable N-38 CF card (1 GB) DVD (Dynamic data acquisition software DCS-100A) *DCS-100A is optional for models with suffix "-0". |
|---|---|
| Optional Accessories |
USB cable N-39 (2 m) Synchronous cable N-128 Camera synchronous cable N-98, N-99, N-101 AC adapter UIA345-12 (For U.S.A.: UNI345-1238) Cable fixture Synchronous extension unit ESYN-30A Remote control unit RCU-41A Battery unit for instantaneous power failure EDB-41B Monitor unit EMON-20A Dummy panel EDX2000-DUMMY |
SANTA TECHNOLOGY CO.,LTD. (Head Office)
35/218 Moo. 2, Leabkhlongsam Rd., Khlongsam, Khlongluang, Pathumthani 12120
Call 02-101-3454 ,089-006-2766
Fax 02-101-3453
Mail. santatech@gmail.com
Line : @santatech
Web : https://santatechnology.com/
