เครื่องวัดไฟฟ้าสถิต Surface resistance meter esd meter ae-780a

SKU: AE-780A
ARMEKA AE-780A ESD Meter ESD Tester ESD Checker เครื่องมือวัดไฟฟ้าสถิตย์ ทดสอบไฟฟ้าสถิต. เครื่องวัดไฟฟ้าสถิต เครื่องวัดESD เครื่องวัดอีเอสดี เครื่องตรวจไฟฟ้าสถิต เครื่องตรวจวัดไฟฟ้าสถิต ARMEKA AE-780A ESD Meter ESD Tester ESD Checker เครื่องมือวัดไฟฟ้าสถ
Availability:

1 in stock

ติดต่อขอใบเสนอราคา

ขอใบเสนอราคา

รายละเอียด

ARMEKA AE-780A ESD Meter ESD, Tester ESD, Checker, เครื่องมือวัดไฟฟ้าสถิตย์, ทดสอบไฟฟ้าสถิต. ARMEKA AE-700 เครื่องวัดความต้านทานผิววัสดุ อีเอสดี Surface Resistance Meter เครื่องวัดไฟฟ้าสถิต เครื่องมือวัดไฟฟ้าสถิต เครื่องตรวจสอบไฟฟ้าสถิตย์ เครื่องมือทดสอบไฟฟ้าสถิตย์ เครื่องวัด ESD.

เครื่องวักวามต้านทานผิววัสดุ อีเอสดี มีเร้งในการวัดอยู่ที่ 103 โอห์ม ถึง 10v-1212 โอห์ม Surface Resistance Meter is designed to measure the resisitance of a target surface.The conductive conduit allows measurements from 103Ω at 10v-1212Ω.

    โดยใช้ มาตรฐานของ เอเอสทีเอ็ม ในการทดสอบ โดยใช้ไฟแอลอีดีแสดงผลค่าการวัด It is based on ASTM Standard D257 testing method. Press and hold the red button on the surface of targeted object LED light will indicate the result of resistance.

    It’s the test results from the Surface Resistance Meter but not according to IEC61340-1-1/2.

    The AE-780ASurface Resistance Checker is a portable battery powered checker fitted with built-in parallel electrodes that allow for tests of material surface resistance. This meter is designed for quick checks of surface resistance for ESD control applications in electronics manufacturing or handling environment. The Surface Resistance Checker is equipped with an automatic test voltage selector. The test voltage will switch from 10V to 100V should the measured resistance exceed 1 x 10E5 ohms. Two banana jacks and an electrode toggle switch allow for the connection of two external 5 pound electrodes that measure surface resistance point to point (RPP) or resistance to equipment ground (RTG).

Compliance Verification Plan “A Compliance Verification Plan shall be established to ensure the Organization’s fulfillment of the technical requirements of the ESD Control Program Plan. Process monitoring (measurements) shall be conducted in accordance with a Compliance Verification Plan that identifies the technical requirements to be verified, the measurement limits and the frequency at which those verifications shall occur. The Compliance Verification Plan shall document the test methods and equipment used for process monitoring and measurements. If the test methods used by the Organization differ from any of the standards referenced in this document, then there must be a tailoring statement that is documented as part of the ESD Control Program Plan. Compliance verification records shall be established and maintained to provide evidence of conformity to the technical requirements.

GENERAL GUIDELINES.

• Use both 5 pound electrodes for RPP.

• Use one 5 pound electrode and one lead to groundable point for RTG (note: groundable points are usually snaps installed on the material or workstation common point ground).

• Ensure that the item being measured is electrically isolated (i.e. placed on an insulative surface) as the checker will measure the lowest resistance path.

• Ensure that the test leads are separated as a best practice.

• When using the 5 pound electrodes.

• Place no closer than 2” from the edge of the surface being measured.

• Place no closer than 3” to any groundable point.

• Place the 5 pound electrodes about 10” apart for RPP of worksurface and 3’ for floor.

• Preferred placements include: most commonly used surface portion, most worn, center, and furthest from groundable point.

• For RTG, connect the banana plug to groundable point.

• If surface has sections (floor tiles, garment panels), for RPP place the 5 pound electrodes on different sections.

ARMEKA expressly warrants that for a period of one (1) year from the date of purchase ARMEKA Surface Resistance Checkers will be free of defects in material (parts) and workmanship (labor). Within the warranty period, a credit for purchase of replacement ARMEKA Surface Resistance Checkers, or, at ARMEKA’s option, the Surface Resistance Checker will be repaired or replaced free of charge. If product credit is issued, the amount will be calculated by multiplying the unused portion of the expected one year life times the original unit purchase price. Call our Customer Service Department at 00358 208 405 488(Finland)or 0086 769 81331736 (China) for a Return Material Authorization (RMA) and proper shipping instructions and address. Please Include a copy of your original packing slip, invoice, or other proof of date Of purchase. Any unit under warranty should be shipped prepaid to the ARMEKA factory. Warranty replacements will take approximately two weeks.

ติดต่อสอบถาม คลิก
อีเมล์
โทรศัพท์
แชทผ่าน LINE
แชทผ่าน Facebook
ดูแผนที่

please wait.....