Universal Recorder EDX-100A-1H

The EDX-100A is a data recorder for measuring up to 256 channels.
Various conditioner cards are available for wide applications.

Specifications

Models	EDX-100A-1H (With DCS-100A) EDX-100A-1H-0 EDX-100A-1H-1 (With DCS-100A and DCS-101A)
Max. Channels	8
Analog Input	Optional conditioner cards Implement with DPM, CDV, CTA, CFV, CCA, CVM installed
CAN Data Input	Accepts one card of CAN-41A
Voice Memo Input	1 channel. Record voice memos included with recordings alongside with measurement data (during manual measurements) using a dedicated remote control(optional accessory)

Sampling Frequency

Sampling Methods	Synchronous sampling of all channels
Sampling Frequency Series	1Hz to 100kHz(1-2-5 series): for 1 channel measurement 1Hz to 10kHz(1-2-5 series): for 16 channel measurement 1Hz to 5kHz(1-2-5 series): for 32 channel measurement 1Hz to 1kHz(1-2-5 series): for CAN data measurement

Data Storage	CF cards recommended by Kyowa (128 MB to 8 GB; 45x speed or higher) Up to 2 GB data for 1 time of measurement
Setting Conditions	Online: From the PC via LAN or USB port Offline: By reading from the CF card which has measuring conditions written with the DCS-100A data acquisition software
Saving Conditions	Amplifier setting conditions and measuring conditions are saved in the internal nonvolatile memory, enabling immediate setup with previous conditions upon power-on.

Measuring Modes

Manual	Data recording is manually started or stopped when data is recorded to a preset number of measured data. Manual mode allows recording of voice memo during data recording.
Trigger	Data recording is automatically started when the preset trigger condition is satisfied. Note that any CAN data mustn't be used as trigger condition
Interval	Data recording is periodically made at preset intervals.

Manual Start/Stop of Data Recording	Possible by using the PC or by pressing the switch on the front panel or from the dedicated remote control unit
Balance Adjustment	Strain input channels are balanced by pressing the BAL. switch on the front panel or from the dedicated remote control unit or from the PC.
Saved Data Format	Kyowa standard format KS2, which enables data analysis with the optional Data Analysis Software DAS-200A
Collecting Data	LAN or USB port enables online data transfer to the PC, while CF card enables offline data transfer.
TEDS	Reads sensor's information and sets to channel condition automatically. [Supported conditioner cards] CDV-40B (-F) DPM-42B (-F) DPM-42B-I (-F) CCA-40A (-F) CDV-44AS CDA-44AS/45AS CVM-41A AD-40AS (-F)
Synchronous Operation	Synchronous cable enables cascade connection of up to 8 units of the EDX-100A. While data is recorded as a separate file in the CF card inserted into each unit, files of all cards are combined into a single file after online or offline data transfer to the PC.
Analog Output	All, except for CDV-40B (-F), AD-40AS (-F), and CAN-41A. Conditioner cards provide an analog output connector, enabling voltage monitoring (±5 VFS).
CF Card Slot	1 (For data recording and condition setting)

Interfaces

	LAN and USB (For control and data transfer), switchable
LAN I/F	10BASE-T/100BASE-TX Connector: RJ45 modular jack
USB I/F	Conforms to USB 2.0 (High speed). Connector: Series B receptacle

Operation Switches	REC/PAUSE: Starts/pauses data recording. STOP: Stops data recording. BAL.: Executes balance adjustment. READ: Reads and sets conditions. ID: Sets ID No. of EDX-100A. LAN/USB: Switches communication port.
Indicators	Operation status indicator LEDs: 7 Channel status indicator LEDs: The number corresponds to the number of channels provided.
External Control Connectors	CONT IN and CONT OUT (For remote control and synchronous operation)
Operating Temperature	0 to 50ºC
Operating Humidity	20 to 90% (Non-condensing)
Storage Temperature	-20 to 60ºC
Vibration Resistant	±29.42 m/s2 (3 G), 5 to 55 Hz (When operating) ±49.03 m/s2 (5 G), 5 to 55 Hz (When not operating)
Impact Resistant	196.1 m/s2 (20 G) /11 ms
Power Supply	10 to 18 VDC Connector: RM12BRD-4PH (Hirose) DC power supply or optional dedicated AC adapter is required.
Current Consumption	Approx. 1.2 A (When operated on 12 VDC with 1 CDV-40B card mounted and full load applied)
Dimensions	70.0 W x 132.5 H x 255 D mm (Excluding protrusions)
Weight	1.6 kg (1.7 kg with 1 CDV-40B card mounted)

Standard Accessories	DC power cable P-76 Ground wire P-72 USB cable N-38 CF card (1 GB) DVD (Dynamic data acquisition software DCS-100A) *DCS-100A is optional for models with suffix "-0".
Optional Accessories	USB cable N-39 (2 m) Synchronous cable N-128 Camera synchronous cable N-98, N-99, N-101 AC adapter UIA345-12 (For U.S.A.: UNI345-1238) Cable fixture Synchronous extension unit ESYN-30A Remote control unit RCU-41A Battery unit for instantaneous power failure EDB-41B Monitor unit EMON-20A Dummy panel EDX2000-DUMMY

SANTA TECHNOLOGY CO.,LTD. (Head Office)
35/218 Moo. 2, Leabkhlongsam Rd., Khlongsam, Khlongluang, Pathumthani 12120
Call 02-101-3454 ,089-006-2766
Fax 02-101-3453
Mail. [email protected]
Line : @santatech
Web : https://santatechnology.com/